20
Jul
Peel back 1-3 inches of backing on one end of the decal. Home Vinyl Tips Tricks Using the Wet Method to Apply Large or Any Decals.
This is according to my conversation with a 3M technical services rep.
Applying vinyl decals wet method. In this video we show how to use the wet application method to apply decals to car windows. For the spray solution we recommend ONLY using DAWN dish soapany. Peel the backing from the decal exposing the adhesive.
Spray the back of the vinyl as you peel it back. Place the decal on the surface ensuring no part of the decal touches a try spot. Maneuver the decal into position decal should float on the surface because both decal and the surfaces should be wet.
This method of vinyl adhesive application allows you to remove air bubbles while at the same time. How to apply vinyl decals using the Wet Application method. Instructions on how to apply vinyl using the wet method.
It allows for the vinyl to be adjusted once it is laid down. Start at one end of the vinyl and work your way to the other end making sure not to leave any air bubbles on the part that has already been laid. If the surface is curved then you may have to use a hair dryer or heat gun to stretch the vinyl and make it fit properly.
The only difference is the application of soapy water to the vinyl before application. By wetting down the vinyl first you are able to reposition your graphics during application. REMEMBER you cannot get the graphics too wet.
The key to this method is keeping both your vinyls and your application surface wet. Cut your vinyl as you normally would and have the surface where you want the vinyl applied ready to go. Make the Solution for Wet Method Application Fill a.
In the above video I am applying overlaminated stickers to a Specialized Kenevo battery and then overlaying the battery stickers with a heavy duty 300micron clear battery protection sticker using the same wet method. This method can be used with almost all vinyl sticker applications. The wet method involves making a soap solution using a mixture of dish soap and water to get both the application surface and the adhesive side of the decal wet before applying the decal.
The soap gives the solution a bit of viscosity to allow the installer to slide the decal around and position it perfectly on the intended target in our case embossed letters or chrome emblems. How to Apply Vinyl. If playback doesnt begin shortly try restarting your device.
Videos you watch may be added to the TVs watch history and influence TV recommendations. To avoid this cancel and sign in to YouTube on your computer. Wet the surface with the wetting solution.
Rub the area with a finger to make sure there are not any dry spots. Spray the area again. Peel back 1-3 inches of backing on one end of the decal.
Leave the rest of the backing attached. On smaller decals you can remove all of the backing. Wet Application Fluid.
You can make you own application fluid with 4 drops of dishwashing liquid dawn joy or baby shampoo etc to 1 quart of water in a spray bottle They go on to describe how to use the fluid to properly align and apply the decal. Has anyone used some type of wet application fluid for your vinyl decals. We are going to applying the decal using the wet method.
The wet method makes it so the decal is easy to move once placed on the side of the car and it helps get rid of air bubbles behind the vinyl. In one spray bottle make a mixture of half water and. Large Decal - Hinge Method - Wet Install - YouTube.
Use the wet method to apply your decals so that you can position everything perfectly. Home Vinyl Tips Tricks Using the Wet Method to Apply Large or Any Decals. Using the Wet Method to Apply Large or Any Decals.
Posted by Bold Apps on January 20 2018. The key to this method is keeping both your vinyls and your application surface wet. First peel your decal away from the wax paper backing.
If your design has several seperate pieces it will come with adhesive masking holding the pieces or letters together. Here is a shortened version of the appropriate steps to take when using the wet wrap installation. Clean the surface of your car with a solvent and water.
Dry with a lint-free cloth. Peel the liner from the back of the vinyl and mist the adhesive side with your application fluid. Make sure not to apply too much.
Wet method is suggested for beginners and larger decals. To use the wet method placement spray the smooth surface with a mixture of soap and water. Wet method is how you install larger images with NO BUBBLES in it and a MUST for frosted vinyl to.
WET APPLICATION METHOD Recommended for hood blackouts stripes any decal larger than 12 If the decal has no transfer tape skip Step 4. Spray car generously with the application spray provided or use a mixture of soapy water in a spray bottle. Peel the backing from the decal exposing the adhesive.
The wet application method applies a vinyl graphic to a substrate by using a fluid to assist with positioning. The dry method as its name indicates does not use fluid but rather depends on the skill of the installer to correctly position the film. Those who are still learning need the flexibility that wetting solutions can offer.
Wet applications will void any warranty of the product itself. The wet solution used and its PH balance may also greatly affect or react with the aluminum layer itself and create a corrosion and breakdown of the material. Adhesive qualities may also be greatly compromised.
This is according to my conversation with a 3M technical services rep.