Homemade fuel line disconnect tool

This 6 piece quick disconnect tool set is designed to quickly and easily remove air conditioning and fuel line disconnect fittings even in hard to reach areas. Enter a new vehicle.

See photo for clarification.

Homemade fuel line disconnect tool. Quick and works just as good. Homemade fuel line quick connect tool - YouTube. How to create a homemade fuel line quick connect removal tool with a bicycle handlebar end cap.

Homemade AC and fuel line disconnect tool constructed from metal flashing. Can be made to fit smaller diameters by cutting off part of the edge. There is a special tool to correctly remove the HPOP lines.

The lines and fittings are made by Aeroquip and are called STC connectors for Snap To Connect. You can remove them with a screw driver but its a pain-in-the-butt usually and you take a chance of damaging the connector hose-end. Ford fuel line removal Hack.

If playback doesnt begin shortly try restarting your device. Videos you watch may be added to the TVs watch history and influence TV recommendations. To avoid this.

Looking at the pipe slip the tool over the pipe with the longer side towards the fitting you want to disconnect then wash inside of fitting with a spray of brake clean to remove any crap or dirt from expansion spring inside fitting then push tool into fitting hard and twist around then pull pipe apart ether side of connector fitting - its hard and sometimes takes many attempts - good luck. 1 Disconnect negative battery cable from the battery. 2 Perform the fuel pressure release procedure.

Refer to the Fuel Pressure Release Procedure in this section. 3 Clean the fitting of any foreign material before disassembly. 4 To disconnect the quick-connect fitting squeeze the plastic retainer tabs Fig.

8 against the sides of. Bore one large holearound one inch through the black pipe. Use a piece of wood as T handlebut keep it about 10 inches long.

Disconnect any wires that stop you from putting your new tool directly on plastic nutthen turn in counterclockwise direction and prestoit unscrews. This helpful puller will handle a variety of injectors found in Cummins engines. Mechanical L-10 PDT and PTD top-stop 855NHIts two-jaw design firmly grips the injector while it is being removed by the slide hammer.

Storage case and a special adapter for pulling STC injectors. Learn how to replace a Ford quick disconnect style fuel filter using a home-made quick disconnect tool made from a pen cap or using a store bought quick disc. Now get your 38th inch fuel line disconnect tool and put it around the hard metal line coming off the fuel rail.

This tool will slip under the connector on the braided steel fuel line and that will undo the metal tangs that hold it onto the fuel rail. See photo for clarification. Swing fuel line out of the way and have rags handy to catch all.

Todd Madden on How-to-remove-push-lock-fuel-line-without-tool. Dec 2 2016 Simply pull out your trusty old soldering gun grab a spade tip and simply cauterize the hose using the same technique as you would with a blade. How to create a homemade fuel line quick connect removal tool with a bicycle handlebar end cap.

The 2nd photo looks to be of the feed line to the fuel distributor from the fuel filter. This uses a Polyamid tube not hose that is pushed onto a barb fitting by means of a special tool. This Poly tube is used in all early CIS systems and currently used by Porsche for the tunnel and much of the later 36 air cooled motors and I think all of.

This Repco Fuel Line Disconnect Tool is built tough and is the ideal garage tool for avid project car enthusiast or home DIYers who want to save some dollars servicing their own daily drivers. Using a fuel line disconnect tool helps you disconnect the fuel line from the connector without causing damage. Enter a new vehicle.

22pcs Master Quick Disconnect Tool Kit for Automotive AC Fuel Line and Transmission Oil Cooler Line Includes Scissor Type Remover Compatible with Most Ford Chevy GM Models. 46 out of 5 stars. Get it as soon as Wed Sep 15.

Fuel Line Disconnect Tool. Special low-profile design works in close quarters on GM Ford and Chrysler vehicles where there is limited clearance between the fuel line fittings and fuel filters fuel rails or sending units. This tool is designed to access the center port on GM fuel tank sending unit.

For 38 and 12 applications. Fuel lines have more pressure in the lines creating a secure connection. Using a fuel line disconnect tool helps you disconnect the fuel line from the connector without causing damage.

The tools put the right amount of pressure on the connection to disconnect with minimal effort on your part. Many fuel lines only disconnect using the specialty tool. This 6 piece quick disconnect tool set is designed to quickly and easily remove air conditioning and fuel line disconnect fittings even in hard to reach areas.

The set includes 78 in 34 in 58 in 12 in 38 in and 516 in. Sizes to accommodate a variety of applications. Remove AC fuel line disconnect fittings.

We have the best Loaner Fuel Line Disconnect Tool for the right price. Buy online for free next day delivery or same day pickup at a store near you. 15 off orders over 100 Free Ground Shipping.