How to change oil in mercruiser alpha one outdrive

Does anyone know what the part is called or. Use your large slotted screw driver and remove the lower plug see image below.

Adjust My Pre-Alpha Alpha One Gen II Outdrive Shift Cable.

How to change oil in mercruiser alpha one outdrive. When adding oil to a MerCruiser Alpha One motor you must unscrew the lower gear case oil plug which is down near the propeller. Quickly attach a hand pump hose attached to oil bottle and pump oil into the drain plug until it overflows out of the vent hole plug. Remove the dipstick and thread the oil hand pump onto the end of the dipstick tube.

If you are using an electric oil changer bucket hook up the hose to the tube and attach the pumps wires to the battery red is positive and black is negative. Replacing drive oil reservoir line on an alpha one gen 2 outdrive Not to drift this off topic but why dont they make those fittings out of brass or whatever instead of cheap plastic. You pros must cringe every time a customer brings in one of those broken off explaining why its going to run 350 to replace the 8 part because you have to remove half the exhaust to get to.

If your drive has an internal drive lube monitor bottle in the boat remove the bottle from its bracket and pour out the old lube. Look in the bottom of the bottle. If you see residue in the bottom of the bottle it should be removed and rinsed out with carb cleaner or Power Tune.

Make sure the bottle is clean and dry. You dont need to change that also do you. Place outdrive in full down position to change oil.

If you let the outdrive drain all night yes the reservoir will empty. To stop this remove reservoir from its bracket. Pinch hose very gently to block the oil flow.

Looking to change gear oil in my alpha one drive. Is there a difference between normal motor oil a marine oil apart from the price I have heaps of different types of oil in the garage for bikes cars etc I cant see why marine oil whould be any different when its doing the same job. The correct way is to pump oil in from the bottom until it comes out your top vent then put in the vent plug and keep pumping oil into the bottom to fill the oil reservoir and oil lines.

It is normal for the oil to burp itself and the oil level in the reservoir to drop a little when you run the drive to get rid of any trapped air. Place an oil drain pan under the drive. Use your large slotted screw driver and remove the lower plug see image below.

If the drain plug is stuck try using an Impact Screwdriver and hammer. You will notice that oil will drain very slowly. Learn how to do an oil change on an Alpha One Gen 2 Sterndrive in four easy steps with our tech support specialist Phil.

In this video you will learn how to-Drain gear lube reservoir in the engine compartment-Drain the sterndrive by removing the lower drain plug-Remove gaskets from both vent and drain plug-Refill with fresh oil. 90-806534970 1096 Alpha One Generation II Sterndrive 2 - 1 Installation Specifications Torque Specifications NOTE. Securely tighten all fasteners not listed below.

Nm Exhaust Pipe to Gimbal Housing Screws 23 31 Propeller Nut 1 55 75 Steering Cable Coupler Nut Tighten Nut Until It Bottoms Out Against Flat Washer then Loosen 12. Two flush-mounted slotted screw caps are located on the left side of the unit. Remove the one at the top then the lower one which will allow the oil to drain out.

Once completely drained connect the fitting on the hose pump to the lower hole insert the pump into the bottle of lower unit oil and pump in the new oil. It is pretty simple to replace you just need to have the upper turned upside down and take a long screwdriver through the exhaust cavity and pry out the old seal. To install the new one you need a suitable driver and rod such as a socket and an extension.

I have a 2000 regal 2100 LSR with a 43 L V6 MerCruiser and a alpha-1 Gentoo outdrive my question is the nipple for the three eights sterndrive fluid broke. Does anyone know what the part is called or. Beginning with the one drive and the TRS outdrive Mercruiser then moved into the production of the Alpha in and then the Bravo sterndrive models in the early s.

Alpha 1 Gen. 2 Outdrive Parts Drawings Videos. Mercruiser Alpha One and Gen.

2 tech support Exploded view diagrams Click here Printer friendly help pages Search by part number or. Oil Reservoir Components for Mercruiser Alpha One Gen Ii Sterndrive Transom Assy Engine Start Over Different Model Different Engine Section OIL RESERVOIR COMPONENTS Reference numbers in this diagram can be found in a light blue row below scroll down to order. 1984 1985 1986 Alpha One Shifting Problems.

Get My Pre-Alpha Alpha One Gen II Outdrive To Shift To Neutral. Adjust My Pre-Alpha Alpha One Gen II Outdrive Shift Cable. Adjust My Bravo Outdrive Shift Cable.

Replace My Pre-Alpha Alpha One Gen II Outdrive Shift Cable. Replace or Adjust My TrimSender Limit Switches. Place an outdrive cart underneath the skeg to hold the drive level.

Secure the outdrive to the cart. Remove all but one of the six nuts from the bell-housing stud with a socket wrench. Leave the last nut loose.

Turn it by hand. Available for single and twin engine applications the Alpha Ones efficient hydrodynamic profile produces very little drag which means better boat performance and fuel economy. Features like an integrated water pump and permanently lubricated pivot points let you spend less time on maintenance and more time boating.

Designed for boats capable of up. Oil change 50 hrs outdrive and engine and only use straight 40 w oil in engine per Mercury manual Have outdrive pressure tested if you notice gear oil reservoir dropping ASAP Check U bolt clamp nuts every 20 hours for loosening factory torque 55 lbs. Check for Gimbal housingsteering pin wear by grabbing end of outdrive and wiggle side to.