07
Sep
Bluetooth Kenwood - YouTube. Installing an Antenna System The antenna system for an SSB Radio on board a sailboat consists of two parts.
3 Run all the engines including AC generators.
How to install a radio in a boat. Black wire goes to the ground red yellow and blue wire go to the positive all other colored wires will go to the speakers positives and neg any power or g if. Connect the power cord to the keyed connector on the power pigtail Connect the antenna and any other accessories. Install the radio in the mounting bracket and connect all cables and accessories to the appropriate jacks and connectors on the back of the radio.
The installation of the antenna is separate from the radio. How to Install a Stereo and Speakers on your Boat. Bluetooth Kenwood - YouTube.
How to Install a Stereo and Speakers on your Boat. Installing a Marine Stereo In Your Boat. DIY install of a Bluetooth satellite-ready stereo.
The back of the stereo is usually supported behind the dash with a bendable metal strap. There is a bolt on the back of the chassis. Push this through the hole in the strap and then twist on the nut to fix it in place.
The front of the stereo can be attached to the dash in several ways. Installing a radio in a bass tracker pro team 170 or in any bass boat like a trac Here is a pic of how mine is mounted. Instead of using a key hot or ign on feed I ran that wire to the accessory switch.
As you can see behind the bunny - - the speakers and the radios are all mounted to the console. On the inside of the console where the. 1 Set the radio between channels at the low end of the spectrum towards the 2 MHz end.
2 Activate other AC and DC equipment one at a time. 3 Run all the engines including AC generators. Brushed electric motor propeller shaft and servo Fig.
Propeller battery pack and electronic speed control ESC Fig. Radio transmitter radio receiver box and battery charger Fig. DIY kit for an RC boat model.
If youre replacing your boats existing radio and speakers you can probably use the same mounting locations and wiring. Otherwise you might need to cut some paneling or run new wires for the components. Most marine receivers are a standard single-DIN 2 tall size and connect to a 12-volt marine battery.
Jensen offers this powered antenna. I installed it inside the radio box. It has a self adhesive pad for mounting though that requires a smooth surface for adhesion.
This radio box required some sanding at the mounting location to make it smooth. It has held fine in seas to 6-feet and speeds to 35-knots No not at the same time. The box doesnt have any controls on it and it can remain tucked behind your stereo.
A satellite ready stereo has the software you need to control the satellite receiver right from the faceplate. In addition you will likely need to purchase a satellite antenna like this one that is specifically designed for marine use. Installing a basic stereo is simple.
There are a number of marine systems available on the market but be sure you select a true waterproof marine model. Select a good location for mounting the stereo receiver. This will depend on the type of boat in which youre performing the installation.
Find a relatively dry spot for mounting. To use TuneLink Elements you need both the device and the mobile app. The first step is downloading the TuneLink Auto app on iTunes or Google Play they have an app for both Apple and Android devices.
Install the app before you are out on the boat ready to use the device. The kit for installing a servo consists of rubber grommets brass bushes and flanged screws. The correct method of fitting these is shown in the diagram.
Note that the bush is inserted from below. To get an idea of the range of sizes and prices of servos which are available visit wwwservoshopcouk. The second method is an AIS transceiver and a VHF radio connected to a low-loss radio frequency RF switching device commonly called a splitter The output of the RF switch connects to the existing VHF cable and antenna so you can have one or the other but not both transmitting simultaneously.
Standard advice for installing a HF Radio on board your boat involves two big steps. Cut the backstay near the stern and near the top of the mast and install insulators to make that isolated section your vertical antenna. Drill a hole in your hull and install a ground shoe A dynaplate to serve as the transmitters ground.
Installing an Antenna System The antenna system for an SSB Radio on board a sailboat consists of two parts. The antenna element and a ground plane. The ground is a very important part of an antenna system and should be given.