How to mount a transducer on a pontoon boat

Unfortunately the mount was one that did not have the flip-up feature found in the newer fishfinder models. Attach the positive and negative connections on the power cable to the boat battery.

Of course knowing which direction youre aiming for isnt enough.

How to mount a transducer on a pontoon boat. That means you should mount your transducer on the same side of your monitor. Usually on the starboard side. Of course knowing which direction youre aiming for isnt enough.

You need to pick an appropriate spot on the ship for mounting. Thankfully the design of pontoon boats makes it simple. FishFinder and Transducer Mount for Pontoons Float Tubes - YouTube.

FishFinder and Transducer Mount for Pontoons Float Tubes. Transducer Placement on a Pontoon Boat Lets make sure we are talking about the proper location. The bracket is not on the top or bottom of the pontoon log.

Its at the back of the pontoon log close to the bottom. Think of the back as a dinner plate. Weld a U shaped aluminim bracket so it does not extend below the pontoon.

DIY Transducer Mount for Inflatable Pontoon Boat - YouTube. DIY Transducer Mount for Inflatable Pontoon Boat. Originally when we purchased the boat the transducer was mounted to the back of a pontoon tube.

Unfortunately the mount was one that did not have the flip-up feature found in the newer fishfinder models. Basically it did not flip up when bumped from the front or when cruising at high speeds as the newer models do. Eventually after a couple of beachings the transducer broke off and.

Pole Arm Transducer Mount for Pontoon Boats and Plastic Jon Boats - YouTube. Many modern pontoons have a bracket welded to the bottom of the pontoon. This is to mount a depth finder or speedometer.

Many pontoons have a removable plug at the bottom of the tube. This is sometimes for pressure testing and. If you intend to install an outboard then you cant mount the transducer there as there is far too much turbulence.

It needs to be on the back end of one of the tubes or mounted using some sort of bracket and pole off the deck. Any welding shop in town should be able to weld on a transducer bracket and it wouldnt or shouldnt cost an arm a leg. Id mount a transducer plate near the bottom of my pontoon then attatch the transducer to the plate.

Secure the plate tot he pontoon with a good silicone adhesive worked for me armchairdeity. Be sure and mount the bracket as close to bottom as possible. Toons make lots of bubbles and disturbed water and transducer needs clean water to work right.

Dont tighten so much it wont kick up when it hits something. Whats going on everybody Rob here with a little video and installing the Stern saver transducer mount for your boat. We just purchased a brand-new fiberglas.

On my 2021 Bass Buggy 16 I mounted the transducer for my Humminbird on the bracket supporting my live well pump that is located on the rear of the port pontoon. Drilled two holes in the aluminum bracket and used the Humminbird mount. Works just fine no prop interference and gives depth reading even at top speed 23 MPH.

2 Mar 4 2006. If you mount the transducer on the rear end of the tube letting it hang just below the tube maybe 12 inch then you shouldnt have any problem with it picking up while moving. I had a pontoon with the bracket factory mounted on the end of the tube and my depth finder worked fine.

Dragging a trailing transducer mounted closely to the transom and below the hull in the trough of a boat forces a powerful flow of already disturbed water into around and over the transducer creating all sorts of sounding chaos. We have accepted this as customary for transom-mounted transducers simply because this is what weve been instructed to doand do our best to deal with it. For twin drives mount the transducer between the drives.

Avoid areas abaft through-hull fittings or pickups that create turbulence. If you opted for a speed sensor connect the cable to the fish finder and spin the paddle wheel to ensure it reads. Make sure there is a.

Use zip ties to connect any loose wire to the pontoon frame. Connect the transducer wire to the back of the depth finder. Attach the positive and negative connections on the power cable to the boat battery.

The positive wire will be red and the negative wire will be black. If mounting a transducer on an aluminum boat we must place a self-adhesive tape above the drill hole location to reduce cracks in the gel coat layer. Using a 4 mm 532 inch drill on marked locations.

Attach the sealant to the supplied 20 mm bolts and attach a transducer assembly to the stern mirror. An optional key is supplied for conventional transducers and straight Down Imaging transducers that can be used to ensure that the transducer is always aligned in the proper position. Downrod length is 48 inches.

Downrod length to water is adjustable by 10 inches to setup your mount so that the transducer will remain in the water even in heavy waves. There is no place to mount a transducer on the bow. There was only one bracket on the back tubes.

I wanted a transducer up fron so I could have better accuracy with the ff. I mounted the transducer bracket on a piece of 1 12 inch pvc. Then I mounted a.