How to put an alternator belt back on

Place first belt around the alternator water pump and crankshaft pulleys. Repeat with the second belt.

Just take the one belt at a time and drop the belt over one fan blade at a time turn the blade and keep moving the belt over the next fan blade.

How to put an alternator belt back on. To put on a new alternator belt youll need to disconnect your car battery and remove the old belt so you can thread the new one through the pulleys. Start by putting on eye. Just take the one belt at a time and drop the belt over one fan blade at a time turn the blade and keep moving the belt over the next fan blade.

Keep doing this so that the entire belt is now hanging over the fan clutch. Install the first belt on the pulleys. Repeat with the second belt.

Take me less than 5 mins to put the belts back on. The pivot bolts on GM typically need a wrench on the rear side and a socket on the front. And the other was the adjustment bolt.

That would usually have a lock-down nut which you have to loosen then use the adjustment bolt to tension the belt. Then tighten the adjustment lock-down nut and then the pivot bolt nut. Remove the belt to see if the whine goes away first.

Then determine which device has a rough bearing or too much play in the pulley. If it appears to be the power steering check the fluid level. Or if you still have it put the old alternator back on.

The offending device will vibrate so you could listen to each one. Increase the tension on the belt. If your vehicle does not have an auto tensioner insert a pry bar or piece of wood between the alternator and the engine.

Run the belt over the. Route the drive belt around all the pulleys except the idler pulley. Install the breaker bar with hex-head socket to the belt tensioner bolt.

Rotate the belt tensioner clockwise in order to relieve the tension on the tensioner. Install the drive belt under the idler pulley. Slowly release the tension on the belt tensioner.

Solved Show A Diagram On Hoe To Put Alternator Belt Back On Fixya Bmw 3 Series E46 Serpentine Belt Replacement Drivediy Related. How To Put Serpentine Belt Back On Alternator. This is a how-to video on a 1999-2000 Mazda Protege 18L Sedan.

It is very easy to install and replace your alternator and belts. Total for parts was 200. Put in the alternator now i need to put back on the belt - Answered by a verified Auto Mechanic.

We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. With the alternator loose move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. Remove the belt once you have enough play between the pulleys.

Place the new belt on and slide the belt tensioner backwards so that the new belt is completely taut. Tighten the belt tensioner bolt with your socket set. The route the belt goes will be on a sticker diagram somewhere under the hood.

Sometimes they are on the under side of the hood while sometimes they are on the cars grill frame. It is usually best to put the belt on all the pulleys except the alternator then pull the tension pulley arm to facilitate the belt slipping onto the alternator pulley. Remember to align the grooves of the belt with the grooves of your pulleys.

Pulleys that dont have any grooves in them receive the flat side of the belt. If you mess up and install the flat side of the rubber belt onto a grooved pulley it will probably split the belt quickly and youll be back where you started but one serpentine belt poorer. Chevy Suburban V8 Two Wheel Drive Automatic I Need A Diagram To Put My Belt Back On.

Hook the other end on the serpentine belt right next to the alternator pulley. If you need to prop the hood up with a stick or something to keep itIf you have determined that your power steering pump is bad here are step-by-step instructions for replacing it. Place first belt around the alternator water pump and crankshaft pulleys.

Tighten the tensioner bolt until the belt is tight along the pulley. There should be no slack on the belt when you pull it with your hands. Ive replaced the alternator on my 2007 TransitHow do you put the belt back on.

The last vehicles I changed the alternator on had a separate tension pulley pushing on the belt or a way of adjusting the tension by moving the alternator out from the engineThis just has the big wheel on the engine and the small wheel on the alternator with three bolts fixing it to the engine. Slide the 38-inch drive bar back into the square opening on the belt tensioner. Turn the belt tensioner clockwise.

Slide the belt over the top of the belt tensioner. Release the belt tensioner so that it tensions against the belt. The tensioner will hold the proper tension against the belt.

Turn the pulley that is connected to the tensioner clockwise with the 12-inch drive pull bar and the 58-inch socket. Reach down with your other hand and pull the belt off of the automatic tensioner pulley. Then remove the belt from the alternator water.