How to replace bilge pump

9 Clean up the tray and surrounding areas with the magic eraser. Bilge pump wont come on.

The bilge pump has a runner volute casingdiffuser and runner blades.

How to replace bilge pump. This video shows how to replace your automatic cartridge bilge pump in you boat. Simply remove the old pump and clip the electrical leads. Splice in the new.

In this video I diagnose and replace a bilge pump in my runabout boat. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube. The bilge pump on my 2000 Sunsetter Lxi keeps blowing the fuse when I flip the switch.

The boat is dry so the bilge pump isnt sitting in water but I figured if I flip the switch to turn it on it should still run regardless. So Im assuming that the pump needs to be replaced. Ive never replaced o.

You should be able to remove your oil tank and battery tray platform to access the bilge and pumps. It may take a bit of reach and contortion but the tank shouldnt need to be pulled. To change a 10 minute part.

But unlike a car dealership thats happy to do it for 130 an hour. I called 3 Aluma craft dealers. One that sold it new.

I bought it with less than 50 hours on it. All 3 told me if I didnt buy it from them. They wouldnt work on it.

Guess thats a long way of saying. Yeh they suck to replace. So my bilge pump is not pumping water out of the boat.

It runs but pumps right back out of the side of the pump into the bilge. I have a 1992 tournament 192 btw. I want to replace the bilge pump but dont know how Im supposed to reach it.

Bilge pumps for boats should be mounted in the lowest part of your bilge. This is where it will be able to collect and pump the most water. If you have a secondary bilge pump it may be located a little higher up.

For small boats one bilge pump is usually sufficient. But as a boat gets larger a second bilge pump is a very good idea. The pump should simply snap off the housing then you can remove it from under the engine and replace.

If you cant reach it them I would just install the new pump in a new place at the same depth in the bilge. Bilge pump wont come on. Think I hit switch when it was parked and didnt realize it.

Is there a fuse that might have blown or do I need to replace the bilge pump 2017 smoker craft 172 pro angler. Believe my bilge pump intake may be plugged up. How do I remove the pump.

07 Challenger 180 SE. From the left side on top there is a locking lever and with both hands you must put the level to the right and with the other hand to unlock the pump cartridge to the left. The pump cartridge is made by johnson pumps with 550gph.

-Cut wires to length on the new pump and crimp new spade lugs on the brown and black wires-Hook up hose using new clamp-Snap pump onto base-Hook up to existing wires-Put some water in the bilge to test-Turn on power-Done. So choose a smooth bilge pump hose. In addition to choosing a smooth bore hose make the path of the hose as straight as possible.

Bends and twists add to the tumult of the water so avoid these if possible. For best results make the hose as short as possible. The bilge pump has a runner volute casingdiffuser and runner blades.

This runner is linked with a motor via a shaft. During the working of the bilge pump as the runner starts rotating the bilge water begins to enter into the runners eye. After passing through the eye the water strikes with the blades of the runner.

Bilge Pump Replacement - AR230. Thread starter SA Abbott. Start date Jul 5 2019.

Tags bilge pump replacement. Tagged users None S. SA Abbott Well-Known Member.

Messages 22 Reaction score 1 Points 55 Location Miami FL Boat Make Yamaha Year 2008 Boat Model AR Boat Length 23 Jul 5 2019 1. 8 Test the pump by installing the rear hull drain plug and filling up the bilge area around the pump. Turn on the bilge and you should see it cycle on drain the water and cycle off when done.

9 Clean up the tray and surrounding areas with the magic eraser. 10 wet vac out the entire bilge area. The bilge pump is usually held in place by two plastic clips that extend straight up from the mount actually part of the mount into two slots on the sides of the pump.

You just need to push these in a little toward the pump body to release them and it sounds like one is already released and then pull the pump straight up. Well evidently this is standard bilge pump hose. I bought 5 of it at West Marine for around 10.

I ended up unscrewing the exit fitting from inside the the hull through the round access hole. I couldnt get a screwdriver onto the hose clamp on the exit fitting so I cut off the fitting and ordered a new one from Yamaha 234 12 Shipping.