24
Jul
I found a 10drum brake kit for sale at Northern Tool for 249 and used a coupon to reduce that to 229 plus tax. Connect the electric brake controller using the free Elecbrakes smartphone app.
Electric trailer brakes operate under a similar principle to an emergency brake only they are not cable operated rather a magnetic piston pulls when energized operating the brakes.
How to set electric trailer brakes. I wanted to do a tutorial on how to set up and adjust electronic brakes for trailers. How to Adjust Electric Trailer Brakes - YouTube. Lift your trailer an support.
The dust cover cap is the metal cap at the center of your hub. Gently tap a screw driver behind the lip and pry the grease dust cap off. Under this cap you will see a large nut along with either a cotter pin or in some newer models and small metal clip over the nut.
You will need to run wiring from the front of your trailer to your trailer brakes to carry electric power to them. In addition to wire you may need connectors zip-ties wire clips electrical tape and ground screws. Youll also have to convert your trailer connector to a 7-way that includes a circuit for electric brakes.
Sounds like you are asking about how tight to adjust your trailers manual-adjust electric drum brakes. You will adjust the brakes using that wheel until there is a slight but constant drag of the shoe pads on the drum. To adjust your brake controller output press and hold the vehicle brake pedal.
Set the output to the starting value specified in the instructions. Then in an open area test the trailer brakes by driving forward at about 25 mph and applying the brakes. If the vehicle stops too slowly increase the maximum output.
Just go slow at first 5mph apply vehicle brakes to see if trailer is braking at all adjust until you feel the trailer braking some but not skidding. Go a little faster 20mph apply brakes to see if you feel trailer braking adjust just a little more if necessary. How to Setup the Trailer Brake Controller.
Ford trucks will automatically apply the same level of pressure you apply to your vehicles brakes to the brakes of what youre towing. However you can also adjust the voltage based on the trailer weight incremental weather and road conditions like gravel versus. Setup Electric Trailer Brakes.
Electric trailer brakes are electrically connected to the tow vehicle utilizing electrical power from the tow vehicle to actuate electromagnetic brake drums. This can also give you the ability to program the brake operation as well as activate the trailer brakes at will if necessary. In order to use electric trailer brakes the tow vehicle needs.
How electric trailer brakes work. Vehicle battery brake control x electromagnetic brake pads trailer deceleration How to Adjust Electric Trailer Brakes. I recently purchased a new tow vehicle that has an integral trailer brake controller with an anti-sway feature.
So I thought I should investigate how hard it would be to add brakes to my trailer. I found a 10drum brake kit for sale at Northern Tool for 249 and used a coupon to reduce that to 229 plus tax. Large boat trailers are typically fitted with an hydraulic brake system where the actuator is an electric over hydraulic device.
This is due to complete electric brake systems not being viable in the marine environment. However this hybrid system still requires a control signal from an electric brake controller. Mount the electric brake controller onto the trailer draw bar.
Plug the electric brake controller into the trailer cable and the tow car socket. Connect the electric brake controller using the free Elecbrakes smartphone app. Mount the device onto the trailer draw bar.
Elecbrakes makes it easy to install an electric brake controller. Electric trailer brakes operate under a similar principle to an emergency brake only they are not cable operated rather a magnetic piston pulls when energized operating the brakes. These are connected to the vehicle through a trailer brake controller which is connected to the vehicles braking system.
Mechanical override brakes use the tow coupling to manually pull a cable connected to the trailers brake drums. These are permitted when the GTM is under 2000kg. They are automatically applied by the brake controller and can be manually operated by a manual control which is installed within reach of the driver.
Drive the trailer out into an open area like an empty parking lot. Get up to around 40 MPH and apply the manual override on your brake controller. Make sure the brake controller is set high enough where it will fully engage the trailer brakes usually the middle setting will be just fine.
The gain on your trailer brake controller must be set every time your trailers weight changes. The gain is what adjusts the amount of braking force that the electric brakes provide. If not set correctly it could create a dangerous situation.
Too little gain will mean that the trailers brakes wont provide enough stopping power. Too much gain and. The first step that you will want to take is to jack the trailer up on properly rated jack stands.
Make sure the trailer is suspended securely before replacing the brakes. Once you have your new electric brakes installed and the hub and drum mounted you will want to move to the back of the brake backing plate. Once the trailer connected message goes away youll see Gain setting.
This is what we talked about earlier and a bar graph that lights up to show you the amount of power going to the trailer brakes. From the trailer display press OK and choose the Connection Checklist option. It corresponds to different trailer types and walks you through the connection process to.