How to tighten an alternator belt

Loosen the bolt in the small block so it doesnt clamp then tightening the bolt on the bracket should tighten the belts then tighten the bolt in the small block so it clamps and holds tension. When you have the alternator in the right position have an assistant tighten the top bolt and nut to lock the alternator.

Loosen the bolts attaching the alternator to the bracket.

How to tighten an alternator belt. How to adjust a Alternator Belt on most old vehicle. So easy a girl can do it. Wait my wife does it in this video so lets watch my wife tighten the Alternat.

Loosen the nut and bolt after which you will have to set the alternator against the belt. Now you need to tighten the slider bolt and the tensioner lock bolt. You even need to check the tension in the belt while tightening it.

Tighten the bolt until there is about 12 inch of slack on the belt. The alternator belt can also be referred to as the serpentine belt or the drive belt. It shouldnt however be confused with the timing belt.

Tighten the alternator bolts. With the serpentine or alternator belt safely seated on the alternator pulley use the same wrench you used to loosen to the bolts to tighten them again. Tightening the Drive Belt with the Alternator Disconnect the battery.

Loosen the bolts attaching the alternator to the bracket. Use a piece of wood as a pry bar to increase the tension on the belt. Tighten the alternator bolts in the new location.

Check the belt tension. Pull the alternator away from the engine until the belt is tight. You want to be able to press down on the belt at a mid point between two pulleys and only be able to move it downward about 18 to 14 inch.

When you have the alternator in the right position have an assistant tighten the top bolt and nut to lock the alternator. How do I adjust the tension on my alternator belt. Insert the pry bar above the alternator pulley.

Apply gentle pressure upwards so that it adds tension to the drive belt. Once the drive belt is moved into its desired tension tighten the adjustment bolt to lock the belt in place. Answer 1 of 3.

Since you gave no information on the make and model of your vehicle I am going to assume it is a modern vehicle like no more than 20 years old. Most vehicles have what is called a serpentine belt. It is a single flat-ribbed belt used to power most if not all of the powered.

Probably change it first the timing belt too as its easier to do them together. On the Sei the whole alternator tensions it. Unbolt both bolts either side move it till the belt is tight and do both bolts up again.

The one bolt is very easy to tighten the other took me my dad and several sockets and spanners to tighten. What you want to do is use the prybar to get the belt tight enough then tighten down the bolt that the alternator pivots on. After you do that then youll tighten the bolt that is in the slot restricting any back and forth movement.

Finally you would tension that last screw that is. Mine squealed on start up after changing tightened it up a hair then it chirped when cranking tightened it up a hair more and its all good. Losten the bottom bolt which is a booger until you get the feel of it then loosen the top and push alternator ttoward the front of the xb to tighten.

How To STOP ALTERNATOR BELT Squeaking Chirping Noise FOREVER. The other end of the alternator will be attached to a slotted slider which allows the alternator to change position to tighten or loosen the belt. Loosening the alternator bolts.

Loosen the pivot bolt as well as the bolt that goes through the adjustment strap. This should relax the alternator and allow some movement. Add tension to the drive belt.

Insert the pry bar above the alternator. How much does it cost to tighten an alternator belt. You want to be able to press down on the belt at a mid point between two pulleys and only be able to move it downward about 18 to 14 inch.

When you have the alternator in the right position have an assistant tighten the top bolt and nut to lock the alternator. Install the alternator to the vehicle and connect the wiring harness. Install the alternator support bracket to the vehicle and tighten the bracket mounting bolts to specifications.

Position the alternator on the mounting bracket. Install and tighten the mounting bolt and nut to 17 ft. Reinstall the drive belt and adjust the tensioner until the proper belt tension is achieved.

Under no circumstances will proclaimliberty2000 be responsible or liable in any way for any content including but not limited to any errors or. As you pry out until the belt is tight tighten the bolt through the adjusting arm slot. Then tighten the bolt that secures the alternator to the engines mounting bracket.

Having a helper tighten the bolt while you hold tension on the belt makes this part easier. How to replace alternator belt if the air conditioner is broken you can use a short serpentine belt without air conditioning. Why do you repeatedly ask vague questions with no informationdetails.

From here on Im just going to ignore anything with your name on it is either a bot or somebody who just asks randomvague questions for some reason. How do I replace a cigarette lighter socket. How do you tighten the alternator belt on a Toyota Corolla.

To slightly tighten the belt loosen the 14mm lower bolt the 12mm upper bracket bolt and then turn the long 12mm tensioner bolt a few turns in the clockwise direction lefty loosy righty tighty. If you adjusted the tension on the new belt start the engine again and listen for any noises. Can you adjust a tensioner pulley.

Loosen the bolt in the small block so it doesnt clamp then tightening the bolt on the bracket should tighten the belts then tighten the bolt in the small block so it clamps and holds tension.