24
Jun
For these seals it is really important to drill the hole and run the screw into the hole. Find Propeller Shaft Seal - 0341281 here.
Thread it with a pipe threaded and grind thread down to a taper.
Johnson outboard prop shaft seal replacement. Ad Lagersmit The origin of sealing solutions. Deliver Peace of Mind with the best sealing solutions for ships pumps and tidal turbines. Propeller seal replacement kit.
Remove the two screws that hold the bearing carrier around the propeller shaft using a screwdriver. Pull the bearing carrier with a flywheel puller. Peel the O-ring out of the groove on the end of the bearing carrier opposite the propeller end and remove.
For these seals it is really important to drill the hole and run the screw into the hole. It will help to prevent you from slipping off the seal and scratching the prop shaft. Both Suzuki Honda have the ability to change the prop shaft seals without pulling the carrier.
The same warnings come with these lower unit seals as well. Changing a Johnson Lower Unit Seal. The lower level of a Johnson outboard houses the water pump and propeller among other important parts.
Two seals keep the water out of the gears and keeps packed grease in so if the seals become damaged in any way this can cause lots of problems. Therefore when a seal is damaged it must be replaced. Hey guys trying to replace the propeller shaft seal on my 1976 johnson 99 10E76G.
I cannot remove the bearing housing as use in salt water seems to have it frozen in. Leeroys Ramblings mentions using a puller or slide hammer with a screw on the end to screw into the seal and tap with a hammer to get it moving but I cannot find any type of puller like this. Removing the Seals.
Clamp the bearing carrier in a vise with protective jaws and pry out the outer and inner prop shaft seals with a pry bar or seal puller being careful not to damage the bore. Dont remove the needle bearing under the seals unless it needs replacement because removal damages the bearing. Changing Evinrude Prop Shaft Seals Video Transcript.
Hey there Dangar Stu here in todays video were going to be changing out the prop shaft oil seal in the Evinrude 150. Ive got to confess I filmed this video on Wednesday its now Sunday morning I went to edit it and realized I hadnt pressed record for the beginning section. Possible to replace prop shaft seals without removing lower unit.
Make you a threaded seal remover from a piece of steel conduit the inside diameter of shaft your working on. Thread it with a pipe threaded and grind thread down to a taper. I had one I used to replace crankshft seal on 15-25 hp motor but loaned it out and never got it back.
Find Bearing Housing to Propeller Shaft Oil Seal - 0321481 here. 5 In Stock - Ships Immediately. Offering discount prices on OEM Evinrude Johnson OMC parts for over 50 years.
Find Propeller Shaft Seal - 0341281 here. 1 In Stock - Ships Immediately. Offering discount prices on OEM Evinrude Johnson OMC parts for over 50 years.
Water in lower unit 60 hp johnson. 18 HP Prop Shaft seal. Water in lower unit oil - 1981 E15RCIS 15hp Evinrude.
1998 200 hp Venom with water in lower unit. Oil Seal For Gearcase Head Assy. Removal Replacement of the Shaft Seals Without Disassembling the Lower Unit.
This section deals with either the driveshaft seal below the water pump OR the prop shaft seals which consist of 2 back to back seals of the same size. This back to back method uses one to keep the water out while the other keeps the oil in. Sierra 18-2032 Oil Seal Sierra replacement oil seal for JohnsonEvinrude Outboards.
GLM 86430 JohnsonEvinrude Outboard 0321788 Mallory 9-76210 Add to Cart. New Red Rhino JohnsonEvinrude 40-60 HP 2-CYL Gearcase Seal Kit 1978-1988 Replaces OEM 396355 This listing is for a New Aftermarket JohnsonEvinrude 40-60 HP 2-Cylinder Gearcase Seal Kit which will fit models from 1978 to 1988. This item will replace OEM No.
Set two new propeller shaft seals into the bearing carrier without lubrication. Tap the seals into the housing with a bearing driver and mallet – the lips of the seal should face the propeller. Apply white marine grease to the lips of the new seal.
Apply white marine grease to a new bearing carrier O-ring and seat the O-ring in the carrier groove. Johnson 8 hp outboard XXXXX I have replaced the propeller shaft seal. Upon reassembly the bushing 0336414 which is installed on the outside of the seal cracked.
Is the bushing critical to operation. How far should it go into the housing. Johnson 8 hp outboard XXXXX I have replaced the propeller shaft seal.
Upon reassembly the bushing 0336414 which is installed on the outside of the seal cracked. Is the bushing critical to operatio. Get it as soon as Thu Sep 16.
FREE Shipping by Amazon. 3865 14 new offers Sierra International 18-2660 Marine Lower Unit Seal Kit for JohnsonEvinrude Outboard Motor white. 35 out of 5 stars.
Rebuilding or Resealing a Johnson Evinrude 6 or 95 Hp Lower Unit Gearcase. I found myself in possession of a 1979 Evinrude 6 Hp outboard that needed its lower unit some people call it the foot rebuilt with a new seal kit. I created a couple of videos detailing the process and have included them below.
The Outboard Expert. Propeller Shaft Care Essentials. Taking care of your propshaft and it will take care of you.
Apply a liberal coating of marine grease to the prop shaft to prevent corrosion between the prop and the shaft. While bad fuel and a dead battery remain the primary reasons a modern outboard. If you see a small thin streak of milky-colored oil coming from the bottom of the lower unit of the motor you must replace the prop shaft seals.
Changing the seals on the prop shaft of Mercruiser engine is a project for winter or the off-season. Replacing the seals themselves is a straightforward job but before you. The outboard is new to me and the pervious owner must have never pulled the prop and wiped off the prop shaft or the area around the seals.
It was just loaded. I also think that I am used to seeing the exhaust from a 1001 mix and this outboard burns 501 so. Ad Lagersmit The origin of sealing solutions.
Deliver Peace of Mind with the best sealing solutions for ships pumps and tidal turbines.