26
Feb
Turn off your battery switches and disconnect the negative battery cables from your batteries. Although being labeled the father of Mercury Outboards its interesting that Kiekhaefer actually worked as a draftsman for Evinrude outboard motors in 1927 however was fired after just 3 months employment with Evinrude.
Mercury-Mercruiser 8M0006027 INJECTOR Fuel.
Mercury outboard fuel injector removal. This video provides fuel injector removal and installation i. How to Remove and Install Fuel injectors on a Mercury Optimax 75 90 and 115 horsepower engines. How to remove outboard fuel injectorsWe service fuel injectors for Outboards Marine Motorcycle Atvs PWCs Cars and Trucks.
Visit us httpfuelinj. I am trying to remove the fuel rail from 2003 25L EFI Mercury. I removed the four bolts and disconnected the wire harness off each injector.
After applying some force the rail wont pull away from the reed block. I thought the rail would come right off. If the injector shows ANY continuity between either pin and the body ground it must be replaced.
Removing Your Fuel Rails The fuel rails must be removed to remove andor replace your Air Injectors. Turn off your battery switches and disconnect the negative battery cables from your batteries. Your fuel rails may be pressurized.
Fuel can cause fire explosion damage injury or death so. Oil Injection System Removal The mercury oil injection system is a popular item to remove especially given its reputation for failure and inability to deliver reliably after 6500 rpm. Remove oil resevoir oil pump mag pickup pump drive shaft then install plug in shaft hole.
Injector Removal Tool Fits Mercury Outboards OE. 91-883521 883521 Removal Tool Injector - 83521 The store will not work correctly in the case when cookies are disabled. Canadian Fuel Injection Service.
35 Ravenhill Dr Kleefeld MB R0A0V2 CA 204 326-0390. Remove the bracket and you can then pop the injectors out after removing the wire clips. To get the air injectors out remove the rail from the cylinder head.
Then after removing the wires from them you can pop them out. Inboard sterndrive and four- and two-stroke outboard motors are all subject to fuel and injector problems. The challenge is the same.
Keeping fresh fuel in the tanks having annual fuel-system maintenance and frequently using the boat. Certified Mercury Tech. 2001 75 hp mercury 4 stroke.
Starts right up idles well. 2001 75 hp mercury 4 stroke. Starts right up idles well.
Then 30 seconds or so into full throttle and it starts to idle down to a full stop. It will usually start. The BAM cleaning process.
Your injectors are externally cleaned visually inspected and numbered. Your injectors are then placed in our digital flow tester and checked for resistance and shorts. Once the electrical test is done they are pressurized and checked for leaks.
Locate the fuel injector rail. You can see it is mounted in place with 2 bolts. Remove these bolts to free the injector rail.
All four injectors can be removed at once. Outboard fuel injector cleaning. Our inboard and outboard fuel injector cleaning service is performed by knowledgeable and experienced technicians.
Included in our service is ultrasonic cleaning before and after flow testing and the replacement of most O-rings and filter baskets. Mercury-Mercruiser 8M0006027 INJECTOR Fuel. 8M0006027 INJECTOR Fuel has been superceded to a new part number.
200250300 PRO 4-STROKE VERADO 6 CYLINDER - 200 PRO VERADO 4-STROKE 6 CYL 200225250275 4-STROKE VERADO - 225 VERADO 4-STROKE 6 CYL 135150175200 4-STROKE - 150 VERADO 4-STROKE 4 CYL. Quicksilver is part of the Mercury Marine family of companies. Quicksilver is the premier supplier of Mercury Marine Original Equipment replacement parts and accessories.
8M0041571 - Fuel Injector Mercury Quicksilver 8M0041571 18183. Outboard EFI engines operate on the fuel injection strategy called SpeedDensity. This means that the ECM primarily looks at the engines speed and the intake manifolds air density in order to calculate the correct amount of fuel to inject.
The engine requires an airfuel mixture of approximately 147 to 1 in the combustion chambers. List Price 18975 17422 Filter Fuel Injector Mercury 150-200 EFI 25L SportJet 240 EFI Mercruiser Cross Ref. 17422 Mfg Part.
35-17422 Not In Stock. Place the fuel cap back on the outboard motor fuel tank. Twist the cap clockwise to tighten and secure the cap to the fuel tank.
Start the boat motor. The outboard fuel injector cleaner will automatically clean the fuel injectors once the motor has been turned on and fuel is distributed into the cylinders. Air pressure from the running motor pressurizes the oil take and pushes everything to the motor.
So as long as you keep your maintenance up check the lines and connections if the motor is running the oil reservoir is pressurized and you should be good to go. Yes you are safe disconnecting it and running pre mix. Although being labeled the father of Mercury Outboards its interesting that Kiekhaefer actually worked as a draftsman for Evinrude outboard motors in 1927 however was fired after just 3 months employment with Evinrude.
Kiekhaefer had 3 unique qualities that made him less than the ideal employee 1 He had a keen eye to see inherent flaws in mechanical designs 2 He often fixated and worked tirelessly trying.